4 Comments

DIY Girls Beaded Heart Personalized Name Necklace – Martha Stewart Jewelry

DIY Girl's Beaded Heart Name Necklace

A couple weeks ago I was chosen to participate in a launch of the new Martha Stewart Jewelry by Plaid available exclusively at Michaels. They sent me an amazingly generous box of jewelry-making supplies and I was floored by the amount of possibilities I could envision. Included were glass beads, cabochons, faceted gems, colored enamels, epoxy clays, decorative molds, findings and tools I didn’t even know existed! In the end, I decided to focus on making a beaded necklace for Chloe.

Considering my limited jewelry-making experience, it was easier than I expected. I call this necklace her personalized “Heart of a Princess” necklace. And if I didn’t think that maybe I was too old for name necklaces (I’m no Carrie Bradshaw, after all), then you’d be seeing me wearing one just like it!

Here is what you’ll need to make your own beaded heart personalized name necklace:

From the Martha Stewart Jewelry line
Supplies (shown in the above photo)
6mm faceted round blue Czech beads
Heart tag silver chain
Hearts blue Czech beads
Strand block letters silver charms
Tools
Flat-nosed pliers & Needle-nosed pliers

Other Supplies
Illusion cord
Crimp beads
Lobster clasp

Note: This makes a 14″ necklace. Extra beads are needed for a longer version.

1. Cut a length of illusion cord 10 inches longer than your final piece. Mine was 24″ long. If you want, tie an end to something (like a key ring) so you don’t have to worry about beads falling off the opposite end. The extra length allows for mishaps and chances are smaller that beads will slip off while I’m working.

2. Remove the silver heart pendants from the Heart Tag Silver Chain by bending open the jump rings with your pliers. Then cut your beads off the packaging and use a bead box, small bowls, or other storage solution to organize and manage your beads.

3. Start by laying out your name, spacing each letter with two clear beads in between (note: small clear beads come with the block letter set). Then begin adding the colored beads to one side of the name, in the order shown below in the diagram.

From each side: sky heart, sky bead, clear bead, silver heart, teal heart, teal bead, clear bead, silver heart (repeat 4 and a half times). Note: be sure the hearts are facing away from the letters on each side.

4. Once your necklace is the desired length, finish it by threading the cord through a crimp bead and a clasp, and then back through the crimp bead. Pull the end until it rests close to your necklace and “crimp” or press the crimp bead flat with your pliers to secure. Do the same to the other end. Try it on and smile!

As you can tell from these photos, the necklace is a little long yet for Chloe at age four. This should give her many years of play and wear, and may even become a treasured keepsake. I love, too, that her favorite color is blue, just like mine. 🙂

Visit Plaid Crafts: Facebook / Twitter / Pinterest
Disclosure: This was a sponsored opportunity via The Blueprint Social, which occasionally provides wonderful opportunities like this one to flex my creative wings. The project idea and opinions are completely my own.
Here are some other projects by bloggers using the Martha Stewart Jewelry line:



5 Comments

Beaded Baby Teether Necklace

Have I mentioned that Leo LOVES hair? Grabbing it, pulling it, playing with it, burying his face in it and even eating it. Sometimes after holding him I feel crunchy places in my hair where he has been sucking. He also sometimes rubs and pulls his own hair to soothe himself. Perhaps I’m raising the next Vidal Sassoon? All I know is that what once was cute when he was less strong is now becoming a bit painful at times. Just ask his poor sister. She basically cannot come within reach of him or she gets grabbed or scratched. Oh yes, he’s also a scratcher. Naturally, he doesn’t mean to, but those little fingernails… well… ouch. I’m just hoping that scab on my nose doesn’t scar.

I made the teething necklace above as an attempt to divert his attention. I’ve seen several fun and funky looking ones, and they are easy enough to make. Basically, you

1. Sew a tube of fabric big enough to insert wooden craft balls.
2. Tie a knot in the fabric between each ball
3. Sew the ends closed and add a ribbon to tie it (or twill tape, in this case).

Leo, however, is only minimally interested. It isn’t hair, after all. And so it doesn’t get  a ton of wear. I tend to prefer smaller jewelry anyway (which I don’t wear now, so as not to have it yanked off and swallowed). Ah, well. Gentle admonishments will have to suffice for now…

Related Posts Plugin for WordPress, Blogger...